Novastar DH7512-S LED Screen Receiving Card
Introduction
The DH7512-S is a general receiving card developed by Xi’an NovaStar Tech Co., Ltd. (hereinafter referred to as NovaStar). A single DH7512-S supports resolutions up to 512×384@60Hz (NovaLCT V5.3.1 or later required).
Supporting various functions such as pixel level brightness and chroma calibration, quick adjustment of dark or bright lines, 3D, individual gamma adjustment for RGB, and image rotation in 90° increments, the DH7512-S can significantly improve the display effect and user experience.
The DH7512-S uses 12 standard HUB75E connectors for communication and supports up to 24 groups of parallel RGB data. On-site setup, operation, and maintenance were all taken into account when designing the hardware and software of the DH7512-S, allowing for an easier setup, more stable operation, and more efficient maintenance.
Certifications
RoHS, EMC Class A
Features
Improvements to Display Effect
⬤Pixel level brightness and chroma calibration
Work with NovaStar’s high-precision calibration system to calibrate the brightness and chroma of each pixel, effectively removing brightness differences and chroma differences, and enabling high brightness consistency and chroma consistency.
⬤Quick adjustment of dark or bright lines
The dark or bright lines caused by splicing of modules and cabinets can be adjusted to improve the visual experience. The adjustment can be easily made and takes effect immediately.
⬤3D function
Working with the sending card that supports 3D function, the receiving card supports 3D image output.
⬤Individual gamma adjustment for RGB
Working with NovaLCT (V5.2.0 or later) and the controller that supports this function, the receiving card supports individual adjustment of red gamma, green gamma and blue gamma, which can effectively control image non- uniformity at low grayscale conditions and white balance offset, allowing for a more realistic image.
⬤Image rotation in 90° increments
The display image can be set to rotate in multiples of 90° (0°/90°/180°/270°).
Improvements to Maintainability
⬤Mapping function
The cabinets can display the receiving card number and Ethernet port information, allowing users to easily obtain the locations and connection topology of receiving cards.
⬤Setting of a pre-stored image in receiving card
The image displayed on the screen during startup, or displayed when the Ethernet cable is disconnected or there is no video signal can be customized.
⬤Temperature and voltage monitoring
The receiving card temperature and voltage can be monitored without using peripherals.
⬤Cabinet LCD
The LCD module of the cabinet can display the temperature, voltage, single run time and total run time of the receiving card.
Improvements to Reliability
⬤Bit error detection
The Ethernet port communication quality of the receiving card can be monitored and the number of erroneous packets can be recorded to help troubleshoot network communication problems.
NovaLCT V5.2.0 or later is required.
⬤Firmware program readback
The receiving card firmware program can be read back and saved to the local computer.
NovaLCT V5.2.0 or later is required.
⬤Configuration parameter readback
The receiving card configuration parameters can be read back and saved to the local computer.
⬤Loop backup
The receiving card and sending card form a loop via the primary and backup line connections. If a fault occurs at a location of the lines, the screen can still display the image normally.
Appearance
⬤Dual program backup
Two copies of firmware program are stored in the application area of the receiving card at the factory to avoid the problem that the receiving card may get stuck abnormally during program update.
All product pictures shown in this document are for illustration purpose only. Actual product may vary.
| Name | Description |
| HUB75E Connectors | Connect to the module. |
| Power Connector | Connect to the input power. Either of the connectors can be chosen. |
| Gigabit Ethernet Ports | Connect to the sending card, and cascade other receiving cards. Each connector can be used as input or output. |
| Self-Test Button | Set the test pattern.After the Ethernet cable is disconnected, press the button twice, and the test pattern will be displayed on the screen. Press the button again to switch the pattern. |
| 5-Pin LCD Connector | Connect to the LCD. |
Indicators
| Indicator | Color | Status | Description |
| Running indicator | Green | Flashing once every 1s | The receiving card is functioning normally. Ethernet cable connection is normal, and video source input is available. |
| Flashing once every 3s | Ethernet cable connection is abnormal. | ||
| Flashing 3 times every 0.5s | Ethernet cable connection is normal, but no video source input is available. | ||
| Flashing once every 0.2s | The receiving card failed to load the program in the application area and is now using the backup program. | ||
| Flashing 8 times every 0.5s | A redundancy switchover occurred on the Ethernet port and the loop backup has taken effect. | ||
| Power indicator | Red | Always on | The power supply is normal. |
Dimensions
The board thickness is not greater than 2.0 mm, and the total thickness (board thickness + thickness of components on the top and bottom sides) is not greater than 8.5 mm. Ground connection (GND) is enabled for mounting holes.
Tolerance: ±0.3 Unit: mm
To make molds or trepan mounting holes, please contact NovaStar for a higher-precision structural drawing.
Pins
|
Pin Definitions (Take JH1 as an example) |
|||||
|
/ |
R1 |
1 |
2 |
G1 |
/ |
|
/ |
B1 |
3 |
4 |
GND |
Ground |
|
/ |
R2 |
5 |
6 |
G2 |
/ |
|
/ |
B2 |
7 |
8 |
HE1 |
Line decoding signal |
|
Line decoding signal |
HA1 |
9 |
10 |
HB1 |
Line decoding signal |
|
Line decoding signal |
HC1 |
11 |
12 |
HD1 |
Line decoding signal |
|
Shift clock |
HDCLK1 |
13 |
14 |
HLAT1 |
Latch signal |
|
Display enable signal |
HOE1 |
15 |
16 |
GND |
Ground |
Specifications
| Maximum Resolution | 512×384@60Hz | |
| Electrical Parameters | Input voltage | DC 3.8 V to 5.5 V |
| Rated current | 0.6 A | |
| Rated power consumption | 3.0 W | |
| Operating Environment | Temperature | –20°C to +70°C |
| Humidity | 10% RH to 90% RH, non-condensing | |
| Storage Environment | Temperature | –25°C to +125°C |
| Humidity | 0% RH to 95% RH, non-condensing | |
| Physical Specifications | Dimensions | 70.0 mm × 45.0 mm × 8.0 mm |
|
Net weight |
16.2 g
Note: It is the weight of a single receiving card only. |
|
| Packing Information | Packing specifications | Each receiving card is packaged in a blister pack. Each packing box contains 80 receiving cards. |
| Packing box dimensions | 378.0 mm × 190.0 mm × 120.0 mm | |
The amount of current and power consumption may vary depending on various factors such as product settings, usage, and environment.
Why do some receiving card have 8 ports, some have 12 ports and some have 16 ports ?
A: One port can load one line modules, so 8 ports can load maximum 8 lines, 12 ports can load maximum 12 lines, 16 ports can load maximum 16 lines.
Can we make any size we want? And what's the best size of led screen?
A: Yes, we can design any size according to your size requirement. Normally, advertising, stage led screen, The best aspect ratio of LED display are W16:H9 or W4:H3
How can i get the goods?
A: We can deliver the goods by express or by sea, pls contact us to select the most favorable delivery way.
How can i pay for the order? Is safe enough?
A: Yes, we provide trade assurance. Payment will be taken until you confirm the goods received in good condition.
What is the payment item?
A: The 30% deposit before production, balance payment 70% before delivery.
Do you test all your goods before delivery?
A: Yes, we have 100% test for 72hrs before delivery.
What can you buy from us?
LED display, LED module, LED power supply, video processor, receiving card, sending card, LED media player and so on.
Can I have a sample order for Led display ?
A: Yes , we welcome sample order to check and test quality. Maxed samples are acceptable.
