G-energy JPS300PV5.0A6 AC to DC Switching Power Supply 5V 60A Output 100V/240V Input for LED Display Screen

Short Description:

The power supply has the characteristics of small volume, high efficiency, stable operation and high reliability. The power supply has input under-voltage, output current limiting, output short circuit and so on. The synchronous rectifier circuit greatly improves the efficiency of the power supply and saves energy consumption. The power supply is wide voltage input, wide ambient temperature, with power factor correction circuit, and has a wide range of applications.

INQUIRY NOW Whatsapp Email

Product Detail

Product Tags

Product Main Specification

Output Power（W）	Rated Input Voltage（Vac）	Rated Output Voltage（Vdc）	Output Current Range（A）	Precision	Ripple andNoise（mVp-p）
300	90-180	+5.0	0-50.0	±2%	≤150mVp-p @25℃(After working at full load for half an hour test）
300	180-264	+5.0	0-60.0	±2%

Environment Condition

Item	Description	Tech Spec	Unit	Remark
1	Working temperature	-30—60	℃	Refer to the use of environmental temperature and load curve.
2	Storing temperature	-40—85	℃
3	Relative humidity	10—90	%
4	Heat dissipation method	Natural cooling
5	Air pressure	80— 106	Kpa

Electrical Character

1	Input character
Item	Description	Tech Spec	Unit	Remark
1.1	Rated voltage range	100-240	Vac	Refer to the diagram of input voltage and load relation.
1.2	Input frequency range	47—63	Hz
1.3	Efficiency	≥88	%	Vin=220Vac 25℃ Output Full Load （ at room temperature)
1.4	Efficiency factor	≥95		Vin=220Vac Rated input voltage, output full load
1.5	Max input current	≤3.5	A
1.6	Dash current	≤120	A	Cold state test @220Vac

2	Output character
Item	Description	Tech Spec	Unit	Remark
2.1	Output voltage rating	+5.0	Vdc
2.2	Output current range	0—60.0	A	Input Voltage 180Vac-264Vac
2.2	Output current range	0—50.0	A	Input Voltage 90-180Vac
2.3	Output voltage adjustablerange	/	Vdc
2.4	Output voltage range	±2	%
2.5	Load regulation	±2	%
2.6	Voltage stability accuracy	±2	%
2.7	Output ripple and noise	≤150 (@25℃)	mVp-p	Rated input, outputfull load, 20MHz bandwidth, load side and 47uf / 104 capacitor
2.8	Start output delay	≤3.0	S	Vin=220Vac @25℃test
2.9	Output voltage raise time	≤100	ms	Vin=220Vac @25℃ test
2.10	Switch machine overshoot	±5	%	conditions: full load,CR mode
2.11	Output dynamic	The voltage change is less than±10% VO ; the dynamic response time is less than 250us	mV	LOAD 25%-50%-25% 50%-75%-50%

3	Protection character
Item	Description	Tech Spec	Unit		Remark
3.1	Input under-voltageprotection	60-80	VAC		Test conditions :full load
3.2	Input under-voltagerecovery point	75-88	VAC		Test conditions :full load
3.3	Output current limitingprotection point	72-90	A		HI-CUP hiccupsself-recovery, avoid long-term damage topower after a short-circuit power.
3.4	Output short circuitprotection	Self-recovery	/
3.5	Overheated protection	/			/
Note:
4	Other character
Item	Description	Tech Spec	Unit	Remark
4.1	MTBF	≥50,000	H
4.2	Leakage Current	＜1(Vin=230Vac)	mA	GB8898-2001 test method

Production Compliance Characteristics

Item	Description			Tech Spec		Remark
1	Electric Strength	Input to output	3000Vac/10mA/1min		No arcing, no breakdown
2	Electric Strength	Input to ground	1500Vac/10mA/1min		No arcing, no breakdown
3	Electric Strength	Output to ground	500Vac/10mA/1min		No arcing, no breakdown

Relative Data Curve

Input voltage and load voltage curve

Load and efficiency curve

The mechanical character and the definition of connectors（ unit：mm）

Dimensions: length× width× height=208×59×30±0.5. MM
Assembly Holes Dimensions

Above is the top view of the bottom shell. The specifications of the screws fixed in the customer system are M3, totaling 4. The length of the fixed screws entering the power supply body should not exceed 3.5mm.

Attention For Application

1、Power supply to be safe insulation, any side of the metal shell with the outside should be more than 8mm safe distance. If less than 8mm need to pad 1mm thickness above PVC sheet to strengthen the insulation.

2、Safe use, to avoid contact with the heat sink, resulting in electric shock.

3、PCB board mounting hole stud diameter not exceeding 8mm.

4、Need a L355mm*W240mm*H3mm aluminum plate as auxiliary heat sink.